First page of the construction of life archive

The Anvil

Posted by Carlota on June 24, 2020 with Comments Closed
in News
as ,

If you can not buy – do it yourself. Board table tops – at least 3 inches, it's better – 5. Surface that would have been better upholstered steel sheet, at least a millimeter thick. But that you could move it myself from the place – you sometimes between the bench and the wall will have something useful to fall. If space allows – to put it up so that we could all sides around. It should be easy for you, that is, him should be comfortable to stand (that would whittle planers or mark something) and sitting (that would be something minor tinkering).

Lighting. Bench should be well lit. (Not to be confused with Prudential!). Afternoon light should give the window – but better to the east and north, because in summer you can not sit in the sun, and direct sunlight is the best option for the job. And the morning sun on a couple of hours in summer and winter will be good. At night, ambient light, reading lamp and carrying – all needed. Location. There will be noisy, there will be a vibration (like a hammer on the anvil will begin to peel or cut piece of metal grinder – so soon and will you have vibration:).

Well ruzhishko experience where you, as not a favorite workshop? OTOH there. Therefore, the workshop should not be in the attic: gudezh will be around the house. You'll be there from time to time tinkering anything at night. Insomnia will visit you, just imagine. And, if you have at dedication middle of the night suddenly shmyaknetsya oxygen cylinder – do not let that be a disaster for family life;). That's why it's better that would shop was a separate building, part of the garage or at least an annex to the house – but not in the house.

Priming Layer

Posted by Carlota on November 18, 2018 with Comments Closed
in News
as ,

Appearance and durability of the coating depends on 60% of the surface preparation by 10-15% – from working properly and the paint by 25-30% – on the quality of the paint itself. Before applying the paint to thoroughly prepare the surface in To ensure high-quality coverage and the duration of his service. Surface preparation is the removal of corrosion products, old paint, grease and other contaminants. You need to see paint cover. If the old paint is firmly on the surface in the form of a continuous layer, it should be washed with warm water and detergent and dry. If the cover is held loosely, it must be fully remove. Surface preparation can be performed chemically and mechanically. In the application of chemical methods of treatment in the alkaline cleaning formulations or active solvent (xylene), depending on the type of pollution, which contributes mainly degreasing the surface.

Mechanical surface cleaning is carried out by: no special tools (brushes, sanding machines), sand fraction, a mixture of sand and water. Using these methods, you can get a good clean surface with a uniform surface roughness, which promotes adhesion of paint film the best. After Priming clean the surface it is applied acrylic primer base coat, which is the basis of coverage. Ground creates a strong bond between the surface and the subsequent paint layers, as well as provides a high protective ability of the coating. Priming produce immediately after the completion of the preparation of the surface. The primer is usually applied with a brush, a paint sprayer. Soil layer should be thin on compared with the outer layers of paint.

The drying of the soil should be carried out under the regime of technology. Shpatlevanie for surfacing must Shpatlevanie. Putty EP-0010 applied in a thin layer as thick and elastic enough layers of fillings can crack during operation, as a result will be lowered protective properties of the coating. Each layer of putty to dry well. The number of layers is not must be greater than three. Recommended thickness of the layer shpatlevochnogo no more than 3 mm. It is better to spend a few days for additional tests fillings, than to bear huge losses due to rework. Grinding Zashpatlevannaya surface after drying has burrs and rough edges, which can be removed by grinding. In the process of grinding the processed surface is exposed to many fine abrasive grains, resulting in formation of the risks and it becomes opaque. This significantly improves the adhesion between the layers of the coating. Grinding with abrasive skin on paper and fabric base.